Skoda Fabia

Since 2000 of release

Repair and car operation


Shkoda Fabija
+ 1.1. The car description
+ 2. The engine
+ 3. Greasing system
+ 4. The power supply system
+ 5. Cooling system
- 6. System of release of the fulfilled gases
   6.1. Check of tightness of system of release of the fulfilled gases
   6.2. Removal and installation of a reception pipe of the muffler (petrol engines)
   6.3. Removal and installation of a reception pipe of the muffler (diesel engines)
   6.4. Replacement of knots of the muffler in gathering (the resonator or the muffler)
   6.5. System рециркуляции the fulfilled gases (engines of 1,4 l, 55 and 74 kw)
   6.6. System рециркуляции the fulfilled gases (engines of 1,9 l, 74 kw)
   6.7. System рециркуляции the fulfilled gases (engines of 1,9 l, 47 kw)
+ 7. Transmission and a running gear
+ 8. A steering
+ 9. Brake system
+ 10. An electric equipment
+ 11. A body
+ 12. Electroschemes





6.3. Removal and installation of a reception pipe of the muffler (diesel engines)

THE GENERAL DATA

System of release of the fulfilled gases of the diesel engine

1 – a lining;
2 – a reception pipe of the muffler;
3 – a nut of fastening of a reception pipe;
4 – a pillow;
5 – an arm;
6 – a nut;

7 – the connecting plug;
8 – a bolt;
9 – an arm with a pillow of back fastening of the muffler;
10 – an arm with a pillow;
11 – labels on a pipe of the muffler;
12 – the muffler with the resonator in gathering
PERFORMANCE ORDER
1. Ослабьте an inhaling of collars of fastening of the connecting plug of a reception pipe and the muffler in gathering.
2. Turn away a nut 3 (fig. System of release of the fulfilled gases of the diesel engine see) fastenings of a reception pipe 2 to a final collector.
3. Accurately separate flanges of a reception pipe 2 and a final collector.
4. Disconnect the bottom ends of pillows of 4 suspension brackets from an arm on a pipe and take out a reception pipe 2 from under the car.
The prevention

Necessarily replace a lining 1 new as at a tightening of nuts of fastening of a reception pipe it it is pressed out and becomes strong unsuitable for a reuse.
5. Carefully clear a flange of a final collector of the rests of an old lining.
6. Establish a new lining 1.
7. Establish into place a reception pipe 2 with the connecting plug 7, having connected the bottom ends of pillows of 4 suspension brackets to an arm. For convenience of work coupling bolts of collars of fastening of the connecting plug 7 it is recommended to have heads downwards.
8. Screw up new nuts 3 (as they самоконтрящиеся) fastenings of a reception pipe to a final collector, having greased preliminary a carving with graphite greasing.
9. Establish the connecting plug 2 so that its edge was on distance and, equal 5 mm from a label 3 on a reception pipe. In this position slightly tighten a coupling bolt of a collar of 1 fastening of the plug on a reception pipe.
10. Shift the muffler in gathering towards a forward part of the car so that distance, measured centre to centre the top and bottom axes of a pillow of 2 suspension brackets of forward fastening of the muffler 1 in gathering, made from 3 to 7 mm.
11. In this position definitively in regular intervals tighten both coupling bolts of collars of fastening of the connecting plug. After that once again would check up distance and if necessary modify it.

The inhaling moments, Нм

Nuts of fastening of a reception pipe to a final collector (on models with the engine capacity of 74 kw)
25
The same (on models with the engine capacity of 47 kw)
40
Coupling bolts of collars of fastening of the connecting plug
40