Skoda Fabia

Since 2000 of release

Repair and car operation

Shkoda Fabija
+ 1.1. The car description
+ 2. The engine
+ 3. Greasing system
+ 4. The power supply system
+ 5. Cooling system
+ 6. System of release of the fulfilled gases
+ 7. Transmission and a running gear
+ 8. A steering
+ 9. Brake system
- 10. An electric equipment
   10.1. Removal and installation of the block of safety locks
   10.2. The storage battery
   + 10.3. Ignition system
   10.4. Removal and installation of a combination of devices
   - 10.5. A cleaner and a windscreen washer
      10.5.1. Adjustment of position of levers with screen wiper brushes
      10.5.2. Removal and installation of a motor-reducer of a screen wiper
      10.5.3. Removal and installation of a tank of a washer from the electropump
      10.5.4. Replacement of jets of a washer
   + 10.6. A cleaner and a washer of glass of a door of a back
   10.7. Replacement of lamps
   10.8. Removal and headlight installation
   10.9. Removal and installation of a back lantern
   10.10. Replacement of an additional lantern of a signal of braking
   10.11. Switches and switches
   10.12. Removal and installation of sound signals
   10.13. Removal and installation динамиков
   10.14. Removal and aerial installation
+ 11. A body
+ 12. Electroschemes

10.5.2. Removal and installation of a motor-reducer of a screen wiper

THE GENERAL DATA

Removal of levers of a cleaner of a windscreen

1 – a decorative cap;

2 – a nut;

3 – the lever;

4 – the platen;

5 – the panel before a windscreen

Screen wiper removal

1 – a bolt;

2 – a screen wiper

Fastening of draughts of a screen wiper to a motor-reducer

1 – draught;

2 – a crank;

3 – a nut;

4 – screws;

5 – a motor-reducer;

6 – an arm

PERFORMANCE ORDER

1. Disconnect a wire from the plug - the storage battery.

2. Accurately having hooked a screw-driver, remove decorative caps 1 (fig. Removal of levers of a cleaner of a windscreen see) from both levers 3 cleaners.

3. Turn on not to the end (not to damage a carving of platens) nuts of 2 fastenings of levers of a screen wiper.

4. By means of flat-nose pliers pull off levers 3 from cones of platens 4 screen wipers.

5. Definitively turn away a nut of 2 fastenings and remove levers 3 from platens.

6. Remove the panel 5 before a windscreen.

7. Holding a screen wiper 2 (fig. screen wiper Removal see) from below, turn away two bolts of 1 its fastening.

8. Remove a screen wiper, having disconnected колодку with wires from a motor-reducer.

9. Having hooked a screw-driver, disconnect both draughts 1 (fig. Fastening of draughts of a screen wiper to a motor-reducer see) from a crank 2.

10. Turn away a nut of 3 fastenings and remove a crank 2.

11. Turn away three screws of 4 fastenings and remove a motor-reducer 5 from an arm 6.

12. Before installation connect колодку with wires to the motor-reducer electric motor (connect then the storage battery) and include a screen wiper that it has occupied a starting position. Again disconnect колодку with wires from the electric motor.

13. Establish a motor-reducer on an arm and fix its screws.

14. Establish a crank 2 with draughts 1 so that it was parallel to draughts and is directed towards the electric motor.

15. Establish a screen wiper upside-down.

16. Adjust position of levers with brushes (subsection 10.5.1 see).

The inhaling moments, Нм

Nuts of fastening of levers of a screen wiper
20

Bolts of fastening of a screen wiper
5

Screws of fastening of a motor-reducer to an arm
8