Skoda Fabia

Since 2000 of release

Repair and car operation



Shkoda Fabija
+ 1.1. The car description
+ 2. The engine
+ 3. Greasing system
+ 4. The power supply system
+ 5. Cooling system
+ 6. System of release of the fulfilled gases
- 7. Transmission and a running gear
   - 7.1. A transmission
      7.1.1. Technical characteristics of transmissions (КП)
      + 7.1.2. Type 002 transmission
      - 7.1.3. A type transmission 02T
         7.1.3.1. Removal and installation
         7.1.3.2. Check of level and oil pouring in a transmission
         7.1.3.3. Replacement of a cover of the lever of a gear change
         7.1.3.4. Removal and installation of a drive of a gear change
         7.1.3.5. Dismantling and assemblage of the mechanism of a gear change
         7.1.3.6. Adjustment of a drive of a gear change
         7.1.3.7. Removal and installation of a drive of forward wheels
   + 7.2. A forward suspension bracket
   + 7.3. A back suspension bracket
+ 8. A steering
+ 9. Brake system
+ 10. An electric equipment
+ 11. A body
+ 12. Electroschemes





7.1.3.7. Removal and installation of a drive of forward wheels
THE GENERAL DATA

Details of a forward suspension bracket

1 – a telescopic rack;
2 – a wheel drive in gathering;
3 – a lock plate;
4 – a bolt of fastening of the case of an internal SHRUS;
5 – a drive of a wheel with internal
SHRUS of "Tripod";
6 – a lock plate ("Tripod");
7 – a bolt of fastening of a drive ("Tripod");
8 – a brake disk;
9 – a bolt of fastening of a wheel;
10 – a nave nut;
11 – the screw of fastening of a brake disk;
12 – brake колодка;
13 – a support;
14 – a directing finger;
15 – a protective cap;
16 – a bolt of fastening of a board of a brake;
17 – a nave;
18 – a brake board;
19 – a nut of a spherical finger of a tip of steering draught;
20 – a tip of steering draught;
21 – a rotary fist;
22 – a nut of a coupling bolt;
23 – a coupling bolt;
24 – the gauge of frequency of rotation of a wheel;
25 – a bolt of fastening of the gauge;
26 – a nut of fastening of a rack of the stabilizer;
27 – a rack of the stabilizer of cross-section stability

Выпрессовка шлицевого a tip of an external SHRUS from a nave

1 – a stripper;

2 – a wheel nave
PERFORMANCE ORDER
1. Ослабьте an inhaling of bolts 9 (fig. of the Detail of a forward suspension bracket see) fastenings of a corresponding wheel and a nut of 10 naves of a wheel.
2. Lift and establish on reliable support a forward part of the car.
3. Remove a wheel and локарь wheel niches.
4. Definitively turn away a nut of 10 naves.
5. Turn away six bolts of 4 fastenings of the case of an internal SHRUS to a flange of a semiaxis and remove three lock plates 3. Suspend for the insurance полуось on a wire to a body.
6. Turn a steering wheel against the stop in that party at which the external tip of steering draught of from outside removed drive will be turned outside from a car axis, and take a shaft aside from a semiaxis flange.
The prevention

On models with the hydraulic booster of a steering do not hold a steering wheel turned in extreme position more than 15 with.


7. By means of a special stripper 1 выпрессуйте шлицевый a tip of an external SHRUS from a nave of 2 wheels (fig. of Vypressovka шлицевого a tip of an external SHRUS from a nave see). In the absence of a stripper it can be made hammer blows through the wooden prorate on an end face шлицевого a tip.
8. Establish a wheel drive upside-down. Thus replace bolts.

The inhaling moments, Нм

Nut of a nave of a wheel
30
Bolts of fastening of the case of an internal SHRUS to a semiaxis flange in two stages on a diagonal:
  – The first stage
10
  – The second stage:
     • М8х48
40
     • М10х52
70
Bolts of fastening of the case of an internal SHRUS of type "Tripod" to a semiaxis flange in two stages on a diagonal:
  – The first stage
10
  – The second stage:
     • М8х18
40
     • М8х28
40
     • М10х23
70
Bolts of fastening of a wheel
120