Skoda Fabia

Since 2000 of release

Repair and car operation

9.8.1. Replacement brake колодок

THE GENERAL DATA

Detachment of a cable of a drive of a lay brake

1 – spring скоба; 2 – a bolt; 3 – a directing finger; 4 – a cable of a drive of a lay brake; 5 – a support; 6 – the lever of a manual drive

Details of the brake disk mechanism of a back wheel

1 – the screw; 2 – a brake disk; 3 – a protective cap; 4 – a nave nut; 5 – a nave; 6 – a bolt of fastening of a brake board; 7 – a brake board; 8 – an axis pin; 9 – the gauge of frequency of rotation of a wheel; 10 – a bolt of fastening of the gauge; 11 – резинометаллическая a support;

12 – a cable of a drive of a lay brake; 13 – a beam of a back suspension bracket; 14 – bolts of fastening directing колодок; 15 – a brake hose; 16 – bolts of fastening of a support; 17 – a support; 18 – external brake колодка; 19 – internal brake колодка; 20 – a spring clamp; 21 – directing колодок

Installation brake колодок

1 – brake колодки; 2 – a spring clamp; 3 – press springs

Replace brake колодки in following cases:

  – A thickness of a frictional overlay of less admissible;
  – The surface of overlays is made oily;
  – Overlays are unsteadily connected to the basis;
  – On overlays deep furrows and сколы.

---

The prevention

колодок it is necessary to replace complete sets at once from both parties of a forward suspension bracket.

Do not apply gasoline, diesel fuel or any other mineral solvents to clearing of brakes.

---

PERFORMANCE ORDER

1. Remove a wheel, preliminary having weakened bolts of its fastening, on the car standing on the earth. 2. Having hooked a screw-driver, remove spring скобу 1 (fig. the Detachment of a cable of a drive of a lay brake see). 3. Having wrung out the lever 6 manual drives in a direction specified by an arrow, disconnect from it a cable 4 drives of a lay brake. 4. Turn away two bolts of 2 fastenings of a support, holding with the second key directing fingers 3 for шестигранники. 5. Remove a support 17 (fig. of the Detail of the brake disk mechanism of a back wheel see) with directing 21 колодок, without disconnecting from it a brake hose 15. Suspend a support on a wire to a suspension bracket spring, watching that the brake hose has not been tense, it was not overwound and strongly it was not bent. 6. Take out from a support 17 brake колодки 18 and 19. 7. From a tank of the main brake cylinder remove by means of a rubber pear a part of a brake liquid. 8. Clear a support. Especially carefully by means of a metal brush clear of an installation site rust колодок, check up, that колодки freely moved in a support. 9. Screw the piston in the cylinder by means of the special adaptation. In the absence of the adaptation it can be made, for example, by means of nippers for removal of lock rings. 10. Establish new brake колодки 1 (fig. Installation brake колодок see) with new spring clamps 2. Press springs 3 should stand in parallel an upper edge колодки. 11. Remove a protective film from a back surface brake колодок. 12. Establish a support 17 (fig. of the Detail of the brake disk mechanism of a back wheel) into place see and fix its new bolts 16 (bolts enter into the complete set new колодок). 13. Connect to the lever 6 (fig. the Detachment of a cable of a drive of a lay brake see) manual drive a cable 4 drives of a lay brake. 14. Establish spring скобу 1. 15. Adjust a lay brake and establish a wheel. Definitively tighten bolts of fastening of a wheel only on the car standing on the earth.

Nominal thickness of a frictional overlay (with the basis), mm	16,9
Is minimum admissible thickness of a frictional overlay (with the basis / without the basis), mm	7,6/2,0