Skoda Fabia

Since 2000 of release

Repair and car operation



Shkoda Fabija
+ 1.1. The car description
- 2. The engine
   2.1. Removal of the top casing of the engine
   + 2.2. Installation of the piston of the first cylinder in position ВМТ of a step of compression
   2.3. Replacement of a belt of a drive of the generator
   + 2.4. Replacement and adjustment of a tension of a belt of a drive of a camshaft
   2.5. Replacement of a chain of a drive of a camshaft
   2.6. Selection of a distributive gear wheel of a cranked shaft
   2.7. Replacement of a lining of a head of the block of cylinders
   2.8. Replacement of an epiploon of a camshaft
   2.9. Replacement маслосъемных caps
   2.10. Replacement of a forward epiploon of a cranked shaft
   2.11. A back epiploon of a cranked shaft
   + 2.12. Repair of a head of the block of cylinders
   + 2.13. Engine repair
+ 3. Greasing system
+ 4. The power supply system
+ 5. Cooling system
+ 6. System of release of the fulfilled gases
+ 7. Transmission and a running gear
+ 8. A steering
+ 9. Brake system
+ 10. An electric equipment
+ 11. A body
+ 12. Electroschemes





2.10. Replacement of a forward epiploon of a cranked shaft
THE GENERAL DATA

THE DIESEL ENGINE

Epiploon of a cranked shaft

I – an epiploon with a spring;

II – an epiploon from material ПТФЭ;

1 – a working edge;

2 – an epiploon

Installation of epiploons of a cranked shaft

1 – a forward epiploon;
2 – a forward cover of the block of cylinders;
3 – the block of cylinders;
4 – a flywheel;
5 – a bolt of fastening of a flywheel;
6 – a guard картера couplings;
7 – a bolt of fastening of the holder of a back epiploon;
8 – the holder of a back epiploon with an epiploon in gathering

Pay attention that on the engine epiploons without поджимных springs, with a ridge working edge 1 are established. It is impossible to grease working edges of these epiploons before installation, the seat on a shaft also should be dry and pure.

PERFORMANCE ORDER
1. Remove локарь the right forward wing.
2. Remove a belt of a drive of a camshaft (subsection 2.4.1 see).
3. Turn away a bolt of 1 fastening of a pulley of a cranked shaft, keeping thus a cranked shaft from проворачивания. On car repair shops for this purpose apply adaptations T 30004 or МР 1-310 (2 – the adaptation; 3 – a pulley of a cranked shaft).
4. Remove a pulley 3 cranked shaft.
5. A stripper of sealing rings МР 1-226 take out an old epiploon.
6. Wipe a cranked shaft a pure rag.
7. Put on a new epiploon a cranked shaft a working edge in the block of cylinders by means of approaching оправки, for example Т 10053/1.
8. Запрессуйте an epiploon against the stop with the help оправки 1. On car repair shops for this purpose apply оправку Т 10053 with bolt Т 10053/2 (1 – оправка Т 10053; 2 – bolt Т 10053/2).

If it is not possible to take out an old epiploon for its replacement it is possible to remove a forward cover of the block of cylinders. For this purpose remove a pulley of a cranked shaft, having followed instructions in item 1-4, then spend following works:

PERFORMANCE ORDER
1. Remove картер the engine (subsection 3.1 see).
2. Turn away bolts of 7 fastenings and remove a forward cover 2. The cover is established on silicone hermetic D176404 А2 without a lining, to tear off it from the block it is possible having brought down not strong blows of a rubber hammer.
3. Take out from a cover 2 forward epiploon 1.
4. Carefully clear of oil and the rests of old hermetic a seat under an epiploon in a cover and interfaced surfaces of a cover and the block of cylinders.
5. Запрессуйте by means of approaching оправки a new epiploon in a cover against the stop.
6. Put on a cover silicone hermetic (the place of drawing of hermetic is shown by an arrow). Thus do not put too thick layer of hermetic, the thickness of a layer should be 2–3 mm.
7. Put on a cranked shaft directing оправку not to damage a working edge of an epiploon, and establish a cover into place. Bolts of fastening of a cover tighten in regular intervals cross-wise the moment 15 Нм.
8. Establish upside-down all removed details. Consider that hermetic dries during 30 mines, therefore to fill in oil in картер the engine it is possible not earlier than through 30 mines after installation картера.

PETROL ENGINES of 1,0 l, 37 kw And 1,4 l, 50 kw

PERFORMANCE ORDER
1. Remove грязезащитный a guard of the right forward wing.
2. Remove a belt of a drive of the generator (subsection 2.3 see).
3. Keeping a cranked shaft from проворачивания, turn away a bolt 18 (fig. the Block of cylinders of engines of 1,0 l, 37 kw and 1,4 l, 50 kw see) pulley fastenings.
4. Remove a pulley 17 drives of the generator.
5. Take out an epiploon 16 of a cover 15 by means of a stripper of sealing rings or having picked up a screw-driver. If the epiploon does not manage to be taken out, it is possible to uncover 15 distributive gear wheels, but in this case it is necessary to replace a lining of 20 covers.
6. Запрессуйте a new epiploon against the stop, a working edge inside.
7. Establish all removed details upside-down.