Skoda Fabia

Since 2000 of release

Repair and car operation



Shkoda Fabija
+ 1.1. The car description
- 2. The engine
   2.1. Removal of the top casing of the engine
   + 2.2. Installation of the piston of the first cylinder in position ВМТ of a step of compression
   2.3. Replacement of a belt of a drive of the generator
   + 2.4. Replacement and adjustment of a tension of a belt of a drive of a camshaft
   2.5. Replacement of a chain of a drive of a camshaft
   2.6. Selection of a distributive gear wheel of a cranked shaft
   2.7. Replacement of a lining of a head of the block of cylinders
   2.8. Replacement of an epiploon of a camshaft
   2.9. Replacement маслосъемных caps
   2.10. Replacement of a forward epiploon of a cranked shaft
   2.11. A back epiploon of a cranked shaft
   + 2.12. Repair of a head of the block of cylinders
   + 2.13. Engine repair
+ 3. Greasing system
+ 4. The power supply system
+ 5. Cooling system
+ 6. System of release of the fulfilled gases
+ 7. Transmission and a running gear
+ 8. A steering
+ 9. Brake system
+ 10. An electric equipment
+ 11. A body
+ 12. Electroschemes





2.8. Replacement of an epiploon of a camshaft
THE GENERAL DATA

DIESEL ENGINES

The epiploon is made of material ПТФЭ. Before epiploon installation it is forbidden to grease its working edge and a camshaft.

PERFORMANCE ORDER
1. Remove a belt of a drive of a camshaft (subsection 2.4.1 see).
2. Keeping a camshaft from проворачивания, turn away bolts of 1 fastening and remove a pulley 2 camshafts (3 – gear sector).
3. Turn away a bolt of 1 fastening of a nave of a pulley of a camshaft on two turns, keeping thus a shaft from проворачивания. On car repair shops for this purpose apply adaptation T 10051 (2 – a nave; 3 – adaptation T 10051).
4. By means of a stripper 1 shift a nave 2 from a camshaft cone. Then remove a stripper, turn out a bolt of fastening of a nave and remove a nave of a pulley of a camshaft.
5. Take out an epiploon. On car repair shops for this purpose apply a stripper of sealing rings Т 30003.
6. Carefully wipe a camshaft to clear of oil and a dirt. Not to damage a working edge of an epiploon, stick with an adhesive tape a flute on a camshaft cone.
7. Accurately put on a new epiploon a camshaft and запрессуйте by means of approaching оправки against the stop.
8. Establish a nave of a pulley and tighten a bolt of its fastening by the moment 100 Нм.
4. By means of a stripper 1 shift a nave 2 from a camshaft cone. Then remove a stripper, turn out a bolt of fastening of a nave and remove a nave of a pulley of a camshaft.
9. Put on a camshaft pulley a nave, thus gear sector 3 (see above) should be above. Screw manually bolts of 1 fastening of a pulley.
10. Establish a belt of a drive of a camshaft and adjust it.

PETROL ENGINES of 1,4 L, 55 And 74 kw

Details of a head of the block of cylinders of engines of 1,4 l, 55 and 74 kw


1 – a bolt of fastening of a pulley;
2 – a pulley of an inlet camshaft;
3 – a camshaft epiploon;
4 – a belt of a drive of a final camshaft;
5 – the case of bearings of camshafts;
6 – a bolt of fastening of the case;
7 – a back cover of an inlet camshaft;
8 – a bolt of fastening of a back cover;
9 – коромысло the valve;
10 – a cracker;
11 – a back cover of a final camshaft;
12 – bolts;
13 – an eye;
14 – the return valve;
15 – a valve hydropusher;
16 – a plate of a spring of the valve;
17 – a valve spring;
18 – маслосъемный a cap;
19 – the repair directing plug of the valve;
20 – the directing plug of the valve;
21 – valves;
22 – a head of the block of cylinders;
23 – a bolt of a tension roller;
24 – a tension roller;
25 – an arm;
26 – a carving stopper;
27 – camshafts;
28 – sealing rings;
29 – a pulley of a final camshaft

PERFORMANCE ORDER
1. Remove belts of a drive of camshafts (subsection 2.4.2 see).
2. Keeping distributive shaft from проворачивания, turn away bolts of 1 fastening and remove pulleys of 2 and 29 camshafts.
3. By means of a stripper of sealing rings or having picked up a screw-driver take out epiploons 3.
4. Wipe camshafts and seats under epiploons to clear of a dirt and oil.
5. Grease a working edge of new epiploons with a thin layer of engine oil.
6. Accurately put on epiploons camshafts and запрессуйте against the stop by means of approaching оправки.
7. Establish pulleys of 2 and 29 camshafts and tighten bolts of 1 their fastening in the beginning the moment 20 Нм, and then tighten for 90 .
8. Establish belts of a drive of camshafts and adjust their tension.
9. For replacement of sealing rings 28 remove the ignition module.
10. Turn away bolts of 8 fastenings and remove back covers of 7 and 11 camshafts.
11. Remove sealing rings 28.
12. Grease with a thin layer of engine oil new rings and establish them into place.
13. Establish covers 7 and 11 into place and tighten bolts of their fastening by the moment 10 Нм.