Skoda Fabia

Since 2000 of release

Repair and car operation

8.4.1. Replacement of a tip of steering draught

THE GENERAL DATA

Fastening of the steering mechanism on the car (without the amplifier)

1 – a plug карданного the hinge; 2 – a coupling bolt; 3 – a nut; 4 – the rotary lever; 5 – a tip of steering draught in gathering with the spherical hinge; 6 – a counternut;

7 – bolts of fastening of a beam of a forward suspension bracket; 8 – bolts of fastening of the steering mechanism; 9 – bolts of fastening of a back support of the power unit; 10 – a back support of the power unit; 11 – a beam of a forward suspension bracket; 12 – the steering mechanism

Выпрессовка a finger of the spherical hinge of a tip of steering draught

1 – a tip; 2 – a stripper; 3 – a nut; 4 – the rotary lever; 5 – draught; 6 – a counternut

Steering draught in gathering

1 – a tip; 2 – a counternut; 3 – draught

Marks of tips of steering draughts

1 – the left tip; 2 – the right tip

Check

PERFORMANCE ORDER

1. At free wheeling increase (люфте) a steering wheel or substantial growth of the effort necessary for its turn, check up axial and radial backlashes in spherical hinges of tips of steering draughts. 2. If at rocking of draught by a hand it is every which way felt люфт in the hinge or there was a corrosion on a spherical finger, replace the spherical hinge in gathering with a tip (check spend at the hung out forward wheels). 3. Necessarily replace a fragmentary protective cover of the spherical hinge, differently the dirt which has got to the hinge and water will quickly put it out of action. The prevention самоконтрящиеся, therefore after everyone отворачивания them it is necessary to replace nuts of fingers of spherical hinges new.

Replacement

PERFORMANCE ORDER

1. Remove a corresponding wheel. 2. Clear a counternut 6 (Fastening of the steering mechanism fig. see the car (without the amplifier)) a tip of steering draught and a nut 3 fingers of the spherical hinge. 3. Ослабьте an inhaling of a counternut 6 tips, keeping from проворачивания the second key draught for шестигранник. 4. Turn away a nut 3 fingers of the spherical hinge. 5. Establish a stripper 2 (fig. of Vypressovka of a finger of the spherical hinge of a tip of steering draught see) and выпрессуйте a finger of the spherical hinge from the rotary lever. 6. If for any reasons draught is disconnected from the rotary lever without replacement of a tip 1, depending on a stripper design leave a nut of 3 fastenings screwed on some coils on a hinge finger not to damage its carving. 7. Disconnect steering draught 5 from the rotary lever 4. 8. Turn away a tip 1 (fig. Steering draught in gathering see), keeping from проворачивания draught 3 for шестигранник. Thus count number of turns of a tip is will help to keep approximately at tip installation a convergence of wheels. The prevention At installation pay attention that the left tip is marked by letter D, and right – C (fig. Marks of tips of steering draughts see). 9. Screw a tip 1 (fig. Steering draught in gathering see) on steering draught 3 on the number of turns counted up earlier. 10. Запрессуйте a hinge finger in the rotary lever 4 (Fastening of the steering mechanism fig. see the car (without the amplifier)), having screwed up a new nut of 3 its fastenings by the corresponding moment (if necessary the finger from проворачивания can be kept with the help шестигранника). 11. After that fix a tip 5 on steering draught a counternut 6, keeping steering draught from проворачивания for шестигранник. 12. Establish a wheel. 13. Check up and if necessary adjust corners of installation of wheels.

The inhaling moments, Нм

Nut of a finger of the spherical hinge	20, then to tighten on 90
Tip counternut	50
Bolts of fastening of a wheel	120