Skoda Fabia

Since 2000 of release

Repair and car operation



Shkoda Fabija
+ 1.1. The car description
+ 2. The engine
+ 3. Greasing system
+ 4. The power supply system
+ 5. Cooling system
+ 6. System of release of the fulfilled gases
+ 7. Transmission and a running gear
- 8. A steering
   8.1. Removal and steering wheel installation
   8.2. Removal and installation of returnable and contact rings in gathering
   + 8.3. A steering column
   - 8.4. The steering mechanism (without the amplifier)
      8.4.1. Replacement of a tip of steering draught
      8.4.2. Removal of the steering mechanism
      8.4.3. Installation of the steering mechanism
      8.4.4. Check and position adjustment рейки the steering mechanism
      8.4.5. Check and backlash adjustment between a gear wheel and рейкой
      8.4.6. Replacement of steering draught
   + 8.5. The steering mechanism (with the amplifier)
+ 9. Brake system
+ 10. An electric equipment
+ 11. A body
+ 12. Electroschemes





8.4.6. Replacement of steering draught
THE GENERAL DATA

Detachment of steering draught from рейки (without the amplifier)

1 – картер the steering mechanism;

2 – рейка;

3 – колпачковая a nut;

4 – steering draught

Fastening of a protective cover of the steering mechanism

1 – картер the steering mechanism;

2 – a collar;

3 – special pincers;

4 – a protective cover;

5 – steering draught

PERFORMANCE ORDER
1. Remove the steering mechanism from the car (subsection 8.4.2 see).
2. Clear the steering mechanism of a dirt, especially in places of landing of protective covers.
3. Remove external 3 (fig. of the Detail of the steering mechanism (a steering without the amplifier see)) and internal 5 collars of fastening of a protective cover.
4. Shift a protective cover 4 aside from картера the steering mechanism.
5. Clamp рейку 2 (fig. the Detachment of steering draught from рейки (without the amplifier)) the steering mechanism in a vice with overlays from soft metal see so that teeths did not get to a vice рейки.
6. Disconnect steering draught 4 from рейки 2, having turned on колпачковую a nut 3.
7. Measure length of old draught. It will help at tip installation on new draught approximately to keep a convergence of wheels.
8. Having turned away a tip 1 (fig. of the Detail of the steering mechanism (a steering without the amplifier see)), remove from draught 6 protective cover 4. Replace the protective cover torn, cracked or lost elasticity.
9. Establish on new draught 6 protective cover 4 with collars 3 and 5 and screw a tip 1 on draught according to earlier measured size.

The prevention

Apply collars of fastening of a protective cover only an original design and manufacture of known manufacturers.


10. Connect steering bent for рейке, having screwed on рейку колпачковую a nut.
11. Clear places of landing of a protective cover 4 on картере the steering mechanism and draught.
12. Grease консистентной with flute greasing in places прилегания a protective cover.
13. Establish a protective cover 4 on seats, watching that it was not overwound.
14. Fix a protective cover 4 (fig. Fastening of a protective cover of the steering mechanism see) new collars 2 by means of special pincers 3.
15. Establish the steering mechanism on the car. Thus modify position of a tip of draught at its connection to the rotary lever.
16. Check up and, if necessary, adjust corners of installation of wheels.

The moment of an inhaling of fastening of steering bent for рейке the steering mechanism – 80 Нм.