Skoda Fabia

Since 2000 of release

Repair and car operation



Shkoda Fabija
+ 1.1. The car description
+ 2. The engine
+ 3. Greasing system
+ 4. The power supply system
+ 5. Cooling system
+ 6. System of release of the fulfilled gases
+ 7. Transmission and a running gear
- 8. A steering
   8.1. Removal and steering wheel installation
   8.2. Removal and installation of returnable and contact rings in gathering
   + 8.3. A steering column
   + 8.4. The steering mechanism (without the amplifier)
   - 8.5. The steering mechanism (with the amplifier)
      8.5.1. Replacement of a tip of steering draught
      8.5.2. Removal of the steering mechanism
      8.5.3. Installation of the steering mechanism
      8.5.4. Replacement of steering draught
      8.5.5. The pump unit
      8.5.6. Check of electric chains of the amplifier of a steering
      8.5.7. Replacement of the gauge of the amplifier of a steering
      8.5.8. Replacement of highways of system of the amplifier of a steering
      8.5.9. Check of level of a working liquid
      8.5.10. Refuelling and removal of air from hydraulic system
      8.5.11. Check and adjustment of corners of installation of wheels
+ 9. Brake system
+ 10. An electric equipment
+ 11. A body
+ 12. Electroschemes





8.5.4. Replacement of steering draught
THE GENERAL DATA

Detachment of steering draught from рейки (with the amplifier)

1 – картер the steering mechanism;

2 – рейка;

3 – колпачковая a nut;

4 – steering draught

PERFORMANCE ORDER
1. Remove the steering mechanism from the car (subsection 8.5.2 see).
2. Clear the steering mechanism of a dirt, especially in places of landing of protective covers.
3. Remove external 3 (fig. of the Detail of the steering mechanism (with the amplifier see)) and internal 5 collars of fastening of a protective cover.
4. Shift a protective cover 4 aside from картера the steering mechanism. At removal of the right draught also shift a protective cover of the left draught to get access to special лыскам for deduction рейки from проворачивания.

The prevention

At a detachment of steering draught from рейки the steering mechanism with the amplifier at all do not clamp рейку the mechanism in a vice – it is possible to damage epiploons of the steering mechanism.


5. Disconnect steering draught 4 (fig. the Detachment of steering draught from рейки (with the amplifier see)) from рейки 2, having turned on колпачковую a nut 3 and keeping thus from проворачивания рейку 2 on the left side for лыски.
6. Measure length of old draught. It will help at tip installation on new draught approximately to keep a convergence of wheels.
7. Having turned away a tip 1 (fig. of the Detail of the steering mechanism (with the amplifier see)), remove from draught 8 protective cover 4. Replace the protective cover torn, cracked or lost elasticity 4.
8. Establish on new draught 8 protective cover 4 with collars 3 and 5 and screw a tip 1 on draught according to earlier measured size.

The prevention

Apply collars of fastening of a protective cover only an original design and manufacture of known manufacturers.


9. Connect steering bent for рейке, having screwed on рейку колпачковую a nut and keeping thus from проворачивания рейку on the left side for лыски.
10. Clear places of landing of a protective cover on картере the steering mechanism and draught.
11. Grease консистентной with flute greasing in places прилегания a protective cover.
12. Establish a protective cover 4 on seats, watching that it was not overwound.
13. Fix a protective cover 4 (fig. Fastening of a protective cover of the steering mechanism see) new collars 2 by means of special pincers 3.
14. Establish the steering mechanism on the car. Thus modify position of a tip of draught at its connection to the rotary lever. Check up and if necessary adjust corners of installation of wheels.

The moment of an inhaling of fastening of steering bent for рейке the steering mechanism – 80 Нм.