Skoda Fabia

Since 2000 of release

Repair and car operation



Shkoda Fabija
+ 1.1. The car description
+ 2. The engine
+ 3. Greasing system
+ 4. The power supply system
+ 5. Cooling system
+ 6. System of release of the fulfilled gases
+ 7. Transmission and a running gear
+ 8. A steering
- 9. Brake system
   + 9.1. Pedal knot
   9.2. The vacuum amplifier
   9.3. The main brake cylinder
   9.4. A pressure regulator (on models without ABS)
   + 9.5. The brake mechanism of a forward wheel of type FS III
   + 9.6. The brake mechanism of a forward wheel of type FS II
   + 9.7. The brake mechanism of a back wheel (drum-type)
   + 9.8. The brake mechanism of a back wheel (disk)
   + 9.9. A lay brake
   - 9.10. Antiblocking system (ABS)
      9.10.1. Check of electroconducting ABS
      9.10.2. Removal and installation of the block of management
      9.10.3. Replacement of the block of management
      9.10.4. Replacement of a wire of the gauge of frequency of rotation of a wheel
      9.10.5. Replacement of the gauge of frequency of rotation of a wheel
      9.10.6. Replacement of touch rings of gauges of frequency of rotation of wheels
      9.10.7. Removal and installation of the switch of a signal of braking
+ 10. An electric equipment
+ 11. A body
+ 12. Electroschemes





9.10.3. Replacement of the block of management
THE GENERAL DATA

Dismantling of the block of management ABS

1, 2, 3, 4, 5, 6 – screws;

7 – the hydraulic device;

8 – the electronic block

The electronic block with the hydraulic device

1 – the hydraulic device;

2 – the valve case;

3 – contacts;

4 – a lining;

5 – the coil;

6 – the electronic block

PERFORMANCE ORDER
1. Remove the block of management from the car (subsection 9.10.2 see).
2. Turn away six screws of fastening of the electronic block 8 (fig. Dismantling of the block of management ABS see) managements to the hydraulic device 7.
3. Remove the electronic block 8 from the hydraulic device 7. Thus do not warp the block, differently valves 2 (fig. the Electronic block with the hydraulic device see) hydraulic device will jam in electromagnetic coils 5 electronic blocks.
4. Accurately wipe the pure rag moistened in spirit, the surface of the hydraulic device 1 interfaced to the electronic block 6. It is forbidden to process this surface any tool (for example, шабером, a file, etc.). With the damaged surface (risks, scratches, etc.), the oxidised or scorched contacts 3 it is necessary to replace the hydraulic device.
5. 4 it is impossible to replace a lining separately, therefore do not remove it.
6. Clear of a dirt a pure rag valves 2, coils 5 and contacts 3. Do not blow their compressed air from a highway as with air oil and water can get. It is forbidden to use also for clearing by solvents and washing liquids.

The prevention

Do not check pump work, bringing pressure to contacts of the hydraulic device as they can scorch.


7. Accurately put on the electronic block the hydraulic device and, having convinced that valves 2 have entered into coils 5, press the block 6 to the hydraulic device 1. Thus the block case should enter for отбортовку the hydraulic device.
8. Screw, definitively without tightening, average screws 1 and 2 (fig. Dismantling of the block of management ABS see) fastenings. Use only the new screws applied on the block of management.

The prevention

It is forbidden to "banish" a defective carving. With the damaged carving it is necessary to replace the hydraulic device.


9. Screw by hand screws 3 and 4, and then 5 and 6 on corners.
10. Definitively tighten all screws the demanded moment in that order (subitem 8 and 9 see).
11. Establish the management block on the car.

The moment of an inhaling of screws of fastening of the electronic block on the hydraulic device – 3 Нм.