Skoda Fabia

Since 2000 of release

Repair and car operation


Shkoda Fabija
+ 1.1. The car description
- 2. The engine
   2.1. Removal of the top casing of the engine
   + 2.2. Installation of the piston of the first cylinder in position ВМТ of a step of compression
   2.3. Replacement of a belt of a drive of the generator
   + 2.4. Replacement and adjustment of a tension of a belt of a drive of a camshaft
   2.5. Replacement of a chain of a drive of a camshaft
   2.6. Selection of a distributive gear wheel of a cranked shaft
   2.7. Replacement of a lining of a head of the block of cylinders
   2.8. Replacement of an epiploon of a camshaft
   2.9. Replacement маслосъемных caps
   2.10. Replacement of a forward epiploon of a cranked shaft
   2.11. A back epiploon of a cranked shaft
   - 2.12. Repair of a head of the block of cylinders
      2.12.1. Dismantling
      2.12.2. Дефектовка
      2.12.3. Assemblage
      2.12.4. Grinding in of valves
      2.12.5. Adjustment of a starting position of hydropushers of valves
      2.12.6. Check of hydropushers of valves of engines of 1,0 l, 37 kw and 1,4 l, 50 kw
      2.12.7. Removal and engine installation
   + 2.13. Engine repair
+ 3. Greasing system
+ 4. The power supply system
+ 5. Cooling system
+ 6. System of release of the fulfilled gases
+ 7. Transmission and a running gear
+ 8. A steering
+ 9. Brake system
+ 10. An electric equipment
+ 11. A body
+ 12. Electroschemes





2.12.3. Assemblage
THE GENERAL DATA

Axis коромысел valves in gathering

1 – direct коромысло;

2 – коромысло, turned to the left;

3 – коромысло, turned to the right;

4 – an external rack of an axis коромысел;

5 – a small rack of an axis коромысел;

6 – the big rack of an axis коромысел

Marks of camshafts of engines in working volume of 1,4 l

1 – an inlet camshaft;

2 – a final camshaft

Block head collect in an order, the return to dismantling, taking into account the following:

PERFORMANCE ORDER
1. Before installation grease with engine oil cores of valves, working surfaces of hydropushers and коромысел valves, маслосъемные caps, cams and necks of camshafts, axes коромысел.
2. At engines of 1,0 l, 37 kw and 1,4 l, 50 kw at assemblage of axes коромысел коромысла and racks arrange, as is shown in fig. the Axis коромысел valves in gathering.
3. At engines of 1,4 l, 55 and 74 kw before installation of epiploons 3 (fig. of the Detail of a head of the block of cylinders of engines of 1,4 l, 55 and 74 kw see) grease with engine oil their working edges. Replace bolts of 1 fastening of pulleys of camshafts and bolts of 6 fastenings of the case of bearings.
4. Marks of camshafts are shown on fig. Marks of camshafts of engines in working volume of 1,4 l. On inlet distributive between cams of the first and second cylinders the inscription 036АС, and between cams of the third cylinder – DE is put a shaft, on final distributive inscriptions 036АА and W1 are accordingly put a shaft.
5. At diesel engines of 1,9 l, 74 kw, before installation of covers of bearings, establish washers 4 (fig. the Head of the block of the diesel engine of 1,9 l, 74 kw see), replace bolts of 1 fastening of axes коромысел and bolts of 19 fastenings of covers of bearings.
6. Before installation of covers of bearings put hermetic on the first and fifth covers, as is shown in fig. of the Place of drawing of hermetic on the first and fifth covers of bearings of a camshaft. Camshaft marks are shown in drawing, at an end face of a cam of the final valve of the fourth cylinder the inscription 038R or 858R, and is put diameter and (a circle entered in a cam) it is equal 52,8 mm.